Our Brands:

Products

Customer Service

Toll Free

Telephone

Contact Us

Seismic & Crack Control Anchor Configurations

Seismic Accessories

Hooks, Pintes & Ties

2X-HOOK™

Byna-Lok™ Wire Tie

Masonry to Concrete

Masonry to Masonry

Masonry to Metal Studs

Lengths

10' (Standard Length)

CUSTOM

Wire Size

3/16" Ø

[ASSET][SUBMITTAL] Submittal 1

[ASSET][SDS] Safety Data Sheet (SDS) 1

[ASSET][SDS] Safety Data Sheet (SDS) 2

[ASSET][SDS] Safety Data Sheet (SDS) 3

[PICKLIST] Lengths

SKU Number

[SM][BOOLEAN] Secures Insulation

[PICKLIST] Wire Diameter

[PICKLIST] Finishes/Materials

[PDF][PART-1] Material Conformance - Text

[PDF][PART-2] Material Conformance - Text

[PDF][PART-3] Material Conformance - Text

[PDF][PART-4] Material Conformance - Text

[PDF][PART-5] Material Conformance - Text

[PDF][PART-1] Submittal Notes

[PDF][PART-2] Submittal Notes

[PDF][PART-1] Submittal Short Description

[PDF][PART-2] Submittal Short Description

[SELLS_WITH][ACCESSORIES] Sells With

[NO_PDF][SM][PICKLIST] High Wind Region

[NO_PDF][SM][PICKLIST] Seismic Region

[NO_PDF][SM][PICKLIST] Wide Cavity Condition

A seismic clip is welded to the 2X-HOOK™ to accept either 9 gauge or 3/16" continuous wire. The compressed leg 2X-HOOK™ has been tested and designed to withstand over 200-lbf, in tension or compression, at maximum allowed offset (ACI 530 6.2.2.5.5.4) of 1-1/4” (disengagement of the pintle from the veneer anchor).&nbsp;AVAILABLE FINISHES:<ul><li>Hot Dip Galvanized</li><li>Type 304 Stainless Steel</li><li>Type 316 Stainless Steel</li></ul>DIMENSIONS:<ul><li>Available lengths: 3", 4", or 4 3/4"</li></ul>

2X-HOOK™ with Welded Seismic Clip

A seismic clip is welded to the 2X-HOOK™ to accept either 9 gauge or 3/16" continuous wire. The compressed leg 2X-HOOK™...

[PICKLIST] Wire Size

Hohmann &amp; Barnard's SH-Seismic Hook:<ul><li>This hook is "swaged" (indented) in two places to accommodate either a 9 gauge or 3/16" continuous wire</li><li>A channel is formed that braces the continuous wire and holds it in place</li><li>Suitable for standard 3/8" joints</li><li>Rectangular hook/pintle acts as a vertically adjustable anchor to bond exterior masonry, while restraining in and out movement.</li><li>Design of hook/pintle serves to mechanically secure insulation to masonry backup.</li><li>Features the same compressed leg design as the 2X-HOOK™ and has been tested and designed to withstand over 200-lbf, in tension or compression, at maximum allowed offset (ACI 530 6.2.2.5.5.4) of 1-1/4” (disengagement of the pintle from the veneer anchor). These results exceed BIA recommendations and the capabilities of standard “round wire” hooks or pintles by over 100%!</li></ul>AVAILABLE FINISHES:<ul><li>Hot Dip Galvanized</li><li>Stainless Steel</li><li>NOTE: H&amp;B Recommends Stainless Steel for maximum protection against corrosion</li></ul>NOTE:<ul><li>U.S. Pat. No. 6,789,365, 7,325,366 &amp; 8,096,090</li><li>Specify "SH" Seismic Hook with: 170 Eye-Wire, 270 Eye-Wire, HB-213, and 2-SEAL Thermal Wing Nuts</li></ul>

2X-SH Compressed Leg SEISMIC HOOK

Hohmann &amp; Barnard's SH-Seismic Hook:This hook is "swaged" (indented) in two places to accommodate either a 9 gauge...

[PDF] Submittal Notes

New masonry veneer can be anchored to studs, existing masonry, concrete or steel with the Byna-Lok Wire Tie. Various H&amp;B Anchor systems can be fitted with the Byna-Lok Wire Tie, affording easy and secure insertion of the continuous joint reinforcing wire. Masonry veneer walls are then reinforced with continuous wire.<ul><li>Swage &amp; mild pitch on legs of the Byna-Lok Wire Tie provide an integral track for the continuous joint reinforcing wire. Suitable for standard 3/8" mortar joint</li><li>Enhanced Performance: The use of a continuous wire in masonry veneer walls is beneficial in providing additional protection against problems arising from thermal expansion and contraction. It also allows for a more uniform distribution of lateral forces.</li><li>Seismic Zone Conformance: This system conforms with the requirements of the Uniform Building Code for seismic zones. The code requires anchored veneer walls to have a continuous wire embedded in the mortar joint. The wire is secured to the tie anchor, which is fastened to the supporting structure.</li><li>More surface engagement of the continuous wire and the integral track than any other system on the market. Reduces potential for incorrect placement or disengagement of the continuous wire due to workmanship error.</li><li>Hassle-free installation of continuous wire into the Byna-Lok Wire Tie</li><li>Economical. Add continuous wire to masonry walls at little additional cost.</li><li>Suitable for use with a variety of H&amp;B anchors.</li><li>System includes heavy-duty continuous wire.</li></ul>AVAILABLE FINISHES:<ul><li>Hot Dip Galvanized</li><li>Type 304 Stainless Steel</li></ul>DIMENSIONS:<ul><li>Available in 3/16" diameter x 3", 4" or 5" long</li></ul>

Byna-Lok™ Seismic Wire Tie

New masonry veneer can be anchored to studs, existing masonry, concrete or steel with the Byna-Lok Wire Tie. Various...

Submittal

LEED Downloads

All H&B product documentation available for download on one page.

Downloads