DESCRIPTION:
Textroflash™ Green is a 40-mil thick composite membrane consisting of a
proprietary clear adhesive laminated to a polyethylene sheet with 45% recycled content.
A silicone release liner prevents the material from sticking together in the
roll and is easily removed for installation. Textroflash™ Green rolls are
75-feet long and are available in widths of 12”, 16”, 18”,
24”, 36”, 48”, 54”, 60” and 72”.
It can be used in both Thru-Wall and
Surface-Mounted applications.
Suitable for application to masonry, gypsum
sheathing, concrete, steel and wood substrates.
NOTES:
- A stainless steel H&B
Drip Plate is required to effectively guide moisture to the exterior
- A
stainless steel H&B Termination Bar (T1 or T2)
must also be used for surface-mount applications
ADVANTAGES:
- Innovative
composite membrane contains 45% Recycled content
- Possible LEED credits toward
certification in categories of Energy & Atmosphere (EA), Materials
& Resources (MR) and Indoor Environmental Quality (EQ)
- Polyethylene sheet aids in
preventing tears or post-installation damage
- Self-adhering
- Self-seals around fastener and
veneer anchor penetrations
- Easy to install, inspect and
repair
INSTALLATION
PERFORMANCE DATA:
GRAB TENSILE |
Warp 240 lb 1068 N |
Weft 250 lb 1110 N |
ASTM D5034-95 |
TONGUE TEAR |
Warp 58 lb 258 N |
Weft 60 lb 266 N |
ASTM D2261-96 |
TRAPEZOIDAL TEAR |
Warp 42 lb 186 N |
Weft 45 lb 200 N |
ASTM S4533-04 |
MULLEN BURST |
500 psi 3449 kPa |
|
ASTM D3786-01 |
ACCELERATED UV WEATHERING1 |
>90 % strength retention after 2000 hrs
exposure @ 0.77 W/m˛/nm, or 1200 hrs exposure @ 1.35 W/m˛/nm |
ASTM G151-00
ASTM G154-04 |
1 Q.U.V. [A-340 Lamps]: 8 hrs UV @ 60o C; 4 hrs
condensation @ 50o C
LIMITATIONS:
- Some substrates may require
prep with Textroflash™ Green primer or Flex-Flash® adhesive
spray.
- Do not apply Flex-Flash®
adhesive spray or Textroflash™ Green to damp, frosty, or
contaminated surfaces
- Cover within 90 days of
installation. (Not intended for longer exposure to weather and UV.)
- Ambient temperature where
installed shall not exceed 150°F
- For best installation install
at temperatures above 32°F.
FLEX-FLASH®
ADHESIVE SPRAY WARNINGS AND HAZARDS (Equivalent to 17.4 Fluid Ounces)
Flex-Flash® adhesive spray contains Acetone and Hexane. Extremely
Flammable. Use with adequate ventilation. Keep away from heat, sparks, open
flame or other ignition sources. Harmful or fatal if swallowed. Do not take internally.
If swallowed do not induce vomiting. Contact a physician immediately. Vapor
harmful. Avoid inhalation of spray mist or vapors. If overcome, move patient to
fresh air. Call a physician immediately. Eye irritant. Avoid contact with eyes
and skin. In case of eye contact, flush immediately with water and continue for
15 minutes. If irritation persists, see a physician. For skin contact, wash
with soap and water. If irritation persists, call a physician immediately.
Contents under pressure. Do not puncture or incinerate container. Do not store
at temperatures above 120°F. KEEP OUT OF REACH OF CHILDREN.
CAS NUMBERS:
Isobutane/Propane Blend 75-28-5/74-98-6; Acetone 67-64-1; Glycerine Ester of
Resin 25038-32-8; Hexane 110-54-3; Block Copolymer 25038-32-8.
Equivalent to 17.4
Fluid Ounces.
VOC INFORMATION: California ARB Consumer
Products Category: Web Spray Adhesive. VOC Standard = 55.0%. VOC Content =
54.9%. This product complies with current applicable CARB standard.
STORAGE
Store flashing materials inside at a temperature between 60° F. (15.5° C.) and 80° F.
(26.6° C.) If exposed to lower temperatures, restore
materials to 60° F. (15.5° C.) minimum temperature before application.
Flex-Flash® should be applied when the air temperature is 32° or higher.
*Note: Hohmann &
Barnard, Inc. is not responsible for incompatibility resulting from the use of
non-H&B mastic and/or recommended primers and sealants.
Home
